The Department of Defense, specifically the Department of the Navy through NAVSUP Weapon Systems Support, is soliciting proposals for the procurement of a switch assembly and other replacement parts, designated as a sole source requirement to General Atomics. The items are critical for a shipboard system that enables the launch and recovery of aircraft, emphasizing the importance of using correct and defect-free materials to prevent serious operational failures. Interested contractors should note that all proposals must comply with the terms of the Basic Ordering Agreement N00383-23-G-SX01, and they can reach out to Michael Dickens at 215-697-4516 or via email at MICHAEL.J.DICKENS5.CIV@US.NAVY.MIL for further inquiries. The solicitation is currently open, and all contractual documents will be considered issued upon transmission by the government.

NSN 1R-1680-016503242-EY, TDP VER 001, QTY 30 EA, DELIVERY FOB ORIGIN. NAVSUP Weapon Systems Support (NAVSUP WSS) Philadelphia intends to solicit on a sole source basis with General Atomics (4V360) for the procurement of the following items: QTY: 30, NSN 5910 016495132, P/N 3890AS003008-01, NRP, Capacitor QTY: 10, NSN 5330 016495224, P/N 3890AS002373-01, Gasket, Cover QTY: 30, NSN 1680 016503242, P/N 3890AS001189-01, NRP, DC Switch Assembly QTY: 10, NSN 1680 016503244, P/N 3890AS001195-01, Enclosure Air Flow There are no drawings/data available. This source is the Original Equipment Manufacturer (OEM) and the only known source for providing repair support of the above repair part. The Government does not own the data or the rights to the data needed to purchase this part from additional sources. All responsible sources may submit a capability statement, proposal, or quotation, which shall be considered by the agency. Source Approval Statement applies to these items. The approved sources for this material are listed above and it is expected that award will be made to this firm. Any firm which is not already approved to manufacture this material must submit a Source Approval Request, SAR. This procurement will not be delayed to wait for a SAR approval. The Government intends to acquire these supplies using the provisions, clauses and procedures prescribed in FAR Part 15. FSC: 1680 NAICS: 336413 This notice of intent is not a request for competitive proposals. However, all proposals received within 45 days (30 days if award is issued under an existing Basic Ordering Agreement (BOA)) after date of publication of this synopsis will be considered by the Government. Information received will normally be considered solely for the purpose of determining whether to conduct a competitive procurement. Electronic procedures will be used for this solicitation. RFP/Solicitation will be posted to NECO. No telephone requests will be honored and no hard copies will be mailed out. Anticipated award date is April 2026. Interested organizations may submit their capabilities and qualifications to perform the effort by email at Michael.j.dickens5.civ@us.navy.mil.

16--NRP,DC SWITCH ASSY - AND OTHER REPLACEMENT PARTS

ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)|19||||||||||||||||||||
TIME OF DELIVERY (JUNE 1997)|20|||||||||||||||||||||
STOP-WORK ORDER (AUG 1989)|1||
WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (JAN 2023)|16|Invoice and receiving report (combo)||TBD|N00383|TBD|TBD|TBD|TBD|||||||||
NAVY USE OF ABILITYONE SUPPORT CONTRACTOR - RELEASE OF OFFEROR INFORMATION (3-18))|1||
VALUE ENGINEERING (JUN 2020)|3||||
INTEGRITY OF UNIT PRICES (NOV 2021)|1||
EQUAL OPPORTUITY FOR WORKERS WITH DISABILITIES (JUN 2020)|2|||
TRANSPORTATION OF SUPPLIES BY SEA (OCT 2024)|2|||
BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM-BASIC (FEB 2024)|11||||||||||||
LIMITATION OF LIABILITY--HIGH-VALUE ITEMS (FEB 1997)|1||
ALTERNATE A, ANNUAL REPRESENTATIONS AND CERTIFICATIONS (OCT 2025)|13||||||||||||||
BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM CERTIFICATE-BASIC (FEB 2024))|5||||||
BUY AMERICAN--BALANCE OF PAYMENTS PROGRAM (FEB 2024)|1||
ROYALTY INFORMATION (APR 1984)|1||
ANNUAL REPRESENTATIONS AND CERTIFICATIONS (MAR 2025)(DEVIATION 2025-O0003 AND 2025-O0004))|12|336413|1250|||||||||||
FACSIMILE PROPOSALS (OCT 1997)|1||
NOTICE OF PRIORITY RATING FOR NATIONAL DEFENSE, EMERGENCY PREPAREDNESS, ANDENERGY PROGRAM USE (APR 2008))|2||x|
This is a spares solicitation for four items. This requirement is sole source to General Atomics (4V360).
This solicitation is being issued in accordance with BOA N00383-23-G-SX01. All terms and conditions of the BOA apply and take precedence over any conflicting terms and conditions contained in this solicitation.
All contractual documents (i.e. contracts, purchase orders, task orders, delivery orders and modifications) related to the instant procurement are considered to be "issued" by the Government when copies are either deposited in the mail, transmitted by facsimile,
or sent by other electronic commerce methods, such as email. The Government's acceptance of the contractor's proposal constitutes bilateral agreement to "issue" contractual documents as detailed herein.
\
1. SCOPE
1.1 . Markings shall be in accordance with MIL-STD-130.
1.2 The material covered in this contract/purchase order will be used in a
crucial shipboard system enabling the launch and/or recovery of aircraft. The use of incorrect or defective material would create a high probability of failure resulting in a serious personnel injury, loss of life, loss of vital
shipboard systems or loss of aircraft. Therefore,the material has been
designated as Critical material and special control procedures are invoked
to ensure receipt of correct material.
1.3 Articles to be furnished hereunder shall be manufactured, tested and inspected in accordance with ;NAWC LAKEHURST; drawing number ( ;(30003); ) ;3890AS003008-01; , Revision ;LATEST REVISION; and all details and specifications referenced therein.
1.4 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be
provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification.
1.5 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C.
2. APPLICABLE DOCUMENTS - NOT APPLICABLE
3. REQUIREMENTS - NOT APPLICABLE
4. QUALITY ASSURANCE PROVISIONS - NOT APPLICABLE.
5. PACKAGING- MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE
6. NOTES - NOT APPLICABLE
THIS IS AN ALRE NON-CRITICAL ITEM. FOR DRAWING UPDATES, SEE ATTACHED NAWC LKE DRAWING UPDATE SHEET.
NAVSUP WSS REFERENCE ONLY: PROCUREMENT TDR 25-10052 WAS UTILIZED IN SUPPORT OF THIS SOLICIATION/CONTRACT.
\
1. SCOPE
1.1 . Markings shall be in accordance with MIL-STD-130.
1.2 The material covered in this contract/purchase order will be used in a
crucial shipboard system enabling the launch and/or recovery of aircraft. The use of incorrect or defective material would create a high probability of failure resulting in a serious personnel injury, loss of life, loss of vital
shipboard systems or loss of aircraft. Therefore,the material has been
designated as Critical material and special control procedures are invoked
to ensure receipt of correct material.
1.3 Articles to be furnished hereunder shall be manufactured, tested and inspected in accordance with ;NAWC LAKEHURST; drawing number ( ;30003; ) ;3890AS002373-01; , Revision ;LATEST; and all details and specifications referenced therein.
1.4 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be
provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification.
1.5 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C.
2. APPLICABLE DOCUMENTS - NOT APPLICABLE
3. REQUIREMENTS - NOT APPLICABLE
4. QUALITY ASSURANCE PROVISIONS - NOT APPLICABLE.
5. PACKAGING- MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE
6. NOTES - NOT APPLICABLE
THIS ALRE ITEM HAS BEEN IDENTIFIED AS NON-CRITICAL.
NAVSUP REFERENCE ONLY: (18-10062):
\
1. SCOPE
1.1 . Markings shall be in accordance with MIL-STD-130.
1.2 The material covered in this contract/purchase order will be used in a
crucial shipboard system enabling the launch and/or recovery of aircraft. The use of incorrect or defective material would create a high probability of failure resulting in a serious personnel injury, loss of life, loss of vital
shipboard systems or loss of aircraft. Therefore,the material has been
designated as Critical material and special control procedures are invoked
to ensure receipt of correct material.
1.3 Articles to be furnished hereunder shall be manufactured, tested and inspected in accordance with ;NAWCAD LAKEHURST; drawing number ( ;(30003); ) ;3890AS001189-01; , Revision ;LATEST; and all details and specifications referenced therein.
1.4 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be
provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification.
1.5 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C.
2. APPLICABLE DOCUMENTS - NOT APPLICABLE
3. REQUIREMENTS - NOT APPLICABLE
4. QUALITY ASSURANCE PROVISIONS - NOT APPLICABLE.
5. PACKAGING- MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE
6. NOTES - NOT APPLICABLE
THIS IS AN ALRE NON-CRITICAL ITEM. FOR DRAWING UPDATES, SEE ATTACHED NAWC LKE DRAWING UPDATE SHEET.
NAVSUP WSS REFERENCE ONLY: PROCUREMENT TDR 25-10028 WAS UTILIZED IN SUPPORT OF THIS SOLICIATION/CONTRACT.
\
1. SCOPE
1.1 . Markings shall be in accordance with MIL-STD-130.
1.2 The material covered in this contract/purchase order will be used in a
crucial shipboard system enabling the launch and/or recovery of aircraft. The use of incorrect or defective material would create a high probability of failure resulting in a serious personnel injury, loss of life, loss of vital
shipboard systems or loss of aircraft. Therefore,the material has been
designated as Critical material and special control procedures are invoked
to ensure receipt of correct material.
1.3 Articles to be furnished hereunder shall be manufactured, tested and inspected in accordance with ;NAWCAD LAKEHURST; drawing number ( ;(30003); ) ;3890AS001195-01; , Revision ;LATEST; and all details and specifications referenced therein.
1.4 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be
provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification.
1.5 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C.
2. APPLICABLE DOCUMENTS
DRAWING DATA=3890AS001195-01 |30003| F| |D| | | |
DRAWING DATA=3890AS001196-01 |30003| B| |D| | | |
3. REQUIREMENTS - NOT APPLICABLE
4. QUALITY ASSURANCE PROVISIONS - NOT APPLICABLE.
5. PACKAGING- MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE
6. NOTES - NOT APPLICABLE
THIS IS AN ALRE NON-CRITICAL ITEM. FOR DRAWING UPDATES, SEE ATTACHED NAWC LKE DRAWING UPDATE SHEET.
NAVSUP WSS REFERENCE ONLY: PROCUREMENT TDR 25-10005 WAS UTILIZED IN SUPPORT OF THIS SOLICIATION/CONTRACT.
\

Buyer

NAICS

PSC

Original Source